Man, that looks like it'll be fairly easy. However, I don't think I'd go 6' with it. I'd keep it at about 4.5', just because that char's nature, it looks like a hilariously evil, little creature!
Anyways, my first thoughts:
1. flat stock of steel, somewhere around 12 ga steel, test before buying to make sure it'll be sturdy enough. Thin for light weight, but thick enough to not bend easily with the creature mounted. Take a few pieces of steel rod that'll fit inside a 1" pvc pipe. Use this for your legs. Welding is required for this part.
2. Get 1" pvc pipe and slide down the shafts. (Make sure your shafts are about the way you want your legs) and build from there. Get the skelly made out so you can build on it.
3. I'd get some chicken wire for the chest and shoulder cavities. Build and sculpt till you're satisfied with it. Take some paper mache and make a bowl at the bottom of chest cavity. Duct tape would work too but a mache bottom leaks less in my experience.
4. I'd duct tape the cavity up about half way. Fill in with foam! Shape / trim foam that comes out any cracks or top. Great stuff would work but best to use an industrial foam for this. Smooth on I hear works great!
5. Once I got my chest done I'd work on the neck and head mounting.
6. Use great stuff foam for the legs and arms. Since they're so stick like, should be easy. Get some gloves and someone to spray the foam into your hands. Wait till it starts to foam up just a bit and start rubbing it on the legs. Build it up past your desired radius. Let set for a full day.
7. I'd start shaping the arms and legs with a wood raft and plastic box cutter. Get the cheap kind that the blades really long and you break them off as they get dull. Extend it all the way out to get wider areas.
8. Get bandaids for all your cuts and pokes.
9. Then I'd resin coat the body. Whichever way you go with, use a mask! Even odorless, if you're using any kind of fibreglass matting or dust, always protect your lungs! I'm speaking from experience (auto body shop... was a painter)
10. I'd rest, set back and look at everything. You can always sand down and add / remove as you needed.
Then come back here and get more advice on the head. I'd get stacks of 2" foam from Home Depot and glue them together, then shape it all out.
You can use a cheap heat gun from harbor freight to heat up the pvc and bend as you needed. I wish I had pics of a creature I did once using this method I mentioned. I'm no pro at all, but this worked fine for me and the monster I made lasted for a few years before breaking, and even then, I don't think it's the creation's fault that a dumb kid tackled it!
Have fun and be safe! Post pics if you start this project, I'm interested in seeing it come to life.
Hope some of this is somewhat helpful.
Dewayne
Summary:
Steel plate for stand.
Metal rods welded where legs will be to help hold it upright.
PvC skeleton made with fittings and heating / bending as needed.
Wire mesh / chicken wire sculp of cavity areas.
Fill with foam.
Shape / trim
Resin coat
Sand / reform / recoat till satisfied.
Should be about 45lbs when finished. Depending on what height you go with.
Anyways, my first thoughts:
1. flat stock of steel, somewhere around 12 ga steel, test before buying to make sure it'll be sturdy enough. Thin for light weight, but thick enough to not bend easily with the creature mounted. Take a few pieces of steel rod that'll fit inside a 1" pvc pipe. Use this for your legs. Welding is required for this part.
2. Get 1" pvc pipe and slide down the shafts. (Make sure your shafts are about the way you want your legs) and build from there. Get the skelly made out so you can build on it.
3. I'd get some chicken wire for the chest and shoulder cavities. Build and sculpt till you're satisfied with it. Take some paper mache and make a bowl at the bottom of chest cavity. Duct tape would work too but a mache bottom leaks less in my experience.
4. I'd duct tape the cavity up about half way. Fill in with foam! Shape / trim foam that comes out any cracks or top. Great stuff would work but best to use an industrial foam for this. Smooth on I hear works great!
5. Once I got my chest done I'd work on the neck and head mounting.
6. Use great stuff foam for the legs and arms. Since they're so stick like, should be easy. Get some gloves and someone to spray the foam into your hands. Wait till it starts to foam up just a bit and start rubbing it on the legs. Build it up past your desired radius. Let set for a full day.
7. I'd start shaping the arms and legs with a wood raft and plastic box cutter. Get the cheap kind that the blades really long and you break them off as they get dull. Extend it all the way out to get wider areas.
8. Get bandaids for all your cuts and pokes.
9. Then I'd resin coat the body. Whichever way you go with, use a mask! Even odorless, if you're using any kind of fibreglass matting or dust, always protect your lungs! I'm speaking from experience (auto body shop... was a painter)
10. I'd rest, set back and look at everything. You can always sand down and add / remove as you needed.
Then come back here and get more advice on the head. I'd get stacks of 2" foam from Home Depot and glue them together, then shape it all out.
You can use a cheap heat gun from harbor freight to heat up the pvc and bend as you needed. I wish I had pics of a creature I did once using this method I mentioned. I'm no pro at all, but this worked fine for me and the monster I made lasted for a few years before breaking, and even then, I don't think it's the creation's fault that a dumb kid tackled it!
Have fun and be safe! Post pics if you start this project, I'm interested in seeing it come to life.
Hope some of this is somewhat helpful.
Dewayne
Summary:
Steel plate for stand.
Metal rods welded where legs will be to help hold it upright.
PvC skeleton made with fittings and heating / bending as needed.
Wire mesh / chicken wire sculp of cavity areas.
Fill with foam.
Shape / trim
Resin coat
Sand / reform / recoat till satisfied.
Should be about 45lbs when finished. Depending on what height you go with.
Comment